33 models

Library, no geometryThreads, screws and nutsremixcad/threadsAn OpenSCAD threading library, written to be used as a component inside other designs rather than printed on its own.4 reusedCC0Metric hex boltremixcad/metric-boltA printable metric hex bolt: hex head, threaded shank, thread pitch taken from the metric standard for the diameter you pick.1 reusedCC0Stackable Mini-ITX NAS casemick/itx-nas-stackA stackable case for a Mini-ITX NAS board, sized so every part prints on a 180 mm bed (Bambu A1 mini).0 reusedMIT8BitDo Micro Phone Clipmick/micro-phone-clipA taco clip that holds an 8BitDo Micro on the lower part of a phone screen, for DS and other retro emulation in portrait.0 reusedMITTiny whoop case sized to its contents, with fitted pockets, snap-pin hinges and a parts boxmick/whoop-caseA hinged travel case for a tiny whoop, its charger and up to fifteen 1S batteries, designed for PETG, with a smooth outside, no loose inserts and no hardware.0 reusedMITOrigami MagSafe wallet and phone stand, printed flat on tullemick/origami-magsafe-walletA MagSafe card wallet that prints flat in one go on a sheet of tulle and folds into shape.0 reusedMITOrigami sleeve wallet, folded from one flat printmick/origami-sleeve-walletA card sleeve wallet that prints as one flat sheet, a few layers high, and is folded into shape like a paper kit.0 reusedMITClamp-on kitchen roll holder for a caravan worktopmick/clamp-kitchen-roll-holderA kitchen roll holder that clamps onto the edge of a worktop, made for a caravan kitchenette.0 reusedMITWall holder for a paper rollmick/paper-roll-holderA wall holder for one paper roll.0 reusedMITDouble wall holder for paper rollsmick/double-roll-holderA wall holder for two paper rolls above each other.0 reusedMITWheeled bipedal balancermick/wheeled-biped-balancerA printable wheeled bipedal balancer with two straight legs and six bus servos: per leg a roll joint low in the chassis, a pitch joint below it, and a wheel drive in the ankle.0 reusedMITBathroom mirror light barmick/mirror-lightA modern wall mounted light bar for above a bathroom mirror.0 reusedMITCat guard for plant potsmick/plant-cat-guardA round grid that lies on the soil of a plant pot so a cat cannot dig in it.0 reusedMITLamp fittings from the Dutch hardware storemick/lamp-fittingsThe four lamp fittings you find on the Dutch hardware store shelf: GU10, GU5.3 (MR16), E14 and E27.0 reusedMITHeadphone stand with desk clampmick/desk-headphone-standA headphone stand that clamps to the edge of a desk: a C-clamp with a printed thumb-screw bolt and a hanger arm at the bottom, reaching out past the edge so the headphones hang in front of the desk.0 reusedMITParametric tractor wheelmick/tractor-wheelA tractor wheel: the parametric car wheel retuned into a tall-sidewall wheel with twelve deep, widely spaced lugs at a steep angle, the tread biting over the shoulder the way an agricultural tyre doe…0 reusedMITParametric car wheelmick/parametric-wheelA complete car wheel: the parametric tyre wrapped around the car rim, with metric hex bolts seated in the lug holes.0 reusedMITParametric car rimmick/parametric-rimA parametric car-style rim: a barrel the tyre grips, a flange at each edge to keep it there, and a closed face disc with a centre bore, a ring of lug holes and round vents.0 reusedMITParametric tyremick/parametric-tyreA parametric tyre.0 reusedMITPhillips driver tipremixcad/phillips-tipA Phillips recess, shown cut into a plain cylinder.0 reusedCC0Threaded rod extenderremixcad/threaded-rod-extenderThe middle section of a rod printed in pieces: threaded to receive a stub at one end and carrying a stub of its own at the other, so extenders chain.0 reusedCC0Threaded rod endremixcad/threaded-rod-endThe end section of a long rod that is printed in pieces: a plain cylinder with a threaded stub on one end, so it screws into the next section.0 reusedCC0Auger threadremixcad/auger-threadAn auger: a deep helical flight wrapped around a thin shaft, rather than the shallow thread of a screw.0 reusedCC0Threaded rodremixcad/threaded-rodA plain externally threaded rod, with no head and no point.0 reusedCC0Metric washerremixcad/metric-washerA flat washer sized to the metric standard for its bolt diameter.0 reusedCC0Metric hex nutremixcad/metric-nutThe hex nut that goes with the metric bolt: standard across flats, standard thickness, internal thread cut to the metric pitch for its diameter.0 reusedCC0Metric wood screwremixcad/metric-wood-screwA countersunk screw with a coarse tapered thread that comes to a point, of the kind that cuts its own way into soft material.0 reusedCC0Metric countersunk boltremixcad/metric-countersunk-boltA metric bolt with a countersunk head and a Phillips recess, so it sits flush with the surface it goes through.0 reusedCC0Gridfinity bin for vase moderemixcad/gridfinity-spiral-vaseA Gridfinity bin drawn as a single continuous wall, so it can be printed in spiral vase mode.0 reusedMITGridfinity bin, lightweightremixcad/gridfinity-lite-binA Gridfinity bin with the solid base replaced by a thin shell, so it uses less filament and less time than the standard bin.0 reusedMITGridfinity baseplateremixcad/gridfinity-baseplateThe plate the bins sit in.0 reusedMITGridfinity binremixcad/gridfinity-binThe standard Gridfinity bin, with compartments, a stacking lip, a label tab and the usual holes in the base for magnets and screws.0 reusedMITLibrary, no geometryGridfinity core modulesremixcad/gridfinity-coreThe module library behind the Gridfinity generators: the grid constants, the base profile, bin bodies, walls, tabs, cutouts, the baseplate, screw and magnet holes, and the geometry helpers they share.0 reusedMIT